当前位置： 首页 > news >正文

RIP动态路由（三层交换机+单臂路由）

news 2025/8/24 20:49:45

RIP动态路由（三层交换机+单臂路由）

31

  • J1 (配置VLAN，修改端口)
Switch>en
Switch>en
Switch#
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#int f0/1
Switch(config-if)#sw
Switch(config-if)#switchport acc vlan 10
% Access VLAN does not exist. Creating vlan 10
Switch(config-if)#ex
Switch(config)#int f0/2
Switch(config-if)#sw acc vlan 20
% Access VLAN does not exist. Creating vlan 20
Switch(config-if)#ex
Switch(config)#int f0/3
Switch(config-if)#sw
Switch(config-if)#switchport mo 
Switch(config-if)#switchport mo 
Switch(config-if)#switchport mo tr
Switch(config-if)#switchport mo trunk
  • 三层交换机(运用SVI)
  • 一定要记得设VLAN
Switch>en
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#vlan 10
Switch(config-vlan)#
Switch(config-vlan)#vlan 20
Switch(config)#int f0/1
Switch(config-if)#sw
Switch(config-if)#switchport t
Switch(config-if)#switchport trunk 
Switch(config-if)#switchport trunk en
Switch(config-if)#switchport trunk encapsulation d
Switch(config-if)#switchport trunk encapsulation dot1q 
Switch(config-if)#sw
Switch(config-if)#switchport m
Switch(config-if)#switchport mode t
Switch(config-if)#switchport mode trunk 
Switch(config-if)#
Switch(config-if)#ex
Switch(config)#int vlan 10
Switch(config-if)#
Switch(config-if)#ip add 192.168.10.254 255.255.255.0
Switch(config-if)#no shutdown 
Switch(config-if)#ex
Switch(config)#int vlan 20
Switch(config-if)#
Switch(config-if)#ip add 192.168.20.254 255.255.255.0
Switch(config-if)#no shut
Switch(config-if)#no shutdown 
Switch(config-if)#ex
Switch(config)#ip routing
Switch(config)#
//配IP
Switch(config)#int f0/2
Switch(config-if)#no switchport 
Switch(config-if)#ip  add 10.10.10.1 255.255.255.0
Switch(config-if)#no shutdown
  • J2
Switch>en
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#int f0/1
Switch(config-if)#sw
Switch(config-if)#switchport acc vlan 10
% Access VLAN does not exist. Creating vlan 10
Switch(config-if)#ex
Switch(config)#int f0/2
Switch(config-if)#sw
Switch(config-if)#switchport acc vlan 20
% Access VLAN does not exist. Creating vlan 20
Switch(config-if)#ex
Switch(config)#int f0/3
Switch(config-if)#sw
Switch(config-if)#switchport m
Switch(config-if)#switchport mode t
Switch(config-if)#switchport mode trunk 
Switch(config-if)#
  • R1
Router>en
Router#
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int g0/0
Router(config-if)#no shut
Router(config-if)#no shutdown Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to upRouter(config-if)#ex
Router(config)#int g0/0.1
Router(config-subif)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0.1, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0.1, changed state to upRouter(config-subif)#en
Router(config-subif)#encapsulation d
Router(config-subif)#encapsulation dot1Q 10
Router(config-subif)#ip add 192.168.30.254 255.255.255.0
Router(config-subif)#ex
Router(config)#int g0/0.2
Router(config-subif)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0.2, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0.2, changed state to upRouter(config-subif)#en
Router(config-subif)#encapsulation d
Router(config-subif)#encapsulation dot1Q 20
Router(config-subif)#
Router(config-subif)#ip add 192.168.40.254 255.255.255.0
Router(config-subif)#ex
Router(config)#int g0/1
Router(config-if)#no shut
Router(config-if)#no shutdown 
Router(config-if)#no shutdown Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to upRouter(config-if)#ip add 10.10.10.2 255.255.255.0
Router(config-if)#ex
Router(config)#int g0/2
Router(config-if)#no shut
Router(config-if)#no shutdown 
Router(config-if)#no shutdown Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/2, changed state to upRouter(config-if)#ip add 20.20.20.1 255.255.255.0
Router(config-if)#
  • J3
Switch>en
Switch#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Switch(config)#int f0/1
Switch(config-if)#sw
Switch(config-if)#switchport acc vlan 10
% Access VLAN does not exist. Creating vlan 10
Switch(config-if)#ex
Switch(config)#int f0/2
Switch(config-if)#sw acc vlan 20
% Access VLAN does not exist. Creating vlan 20
Switch(config-if)#ex
Switch(config)#int f0/3
Switch(config-if)#sw mo tr
Switch(config-if)#sw mo trunk 
Switch(config-if)#
  • R2
Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int g0/0
Router(config-if)#no shut
Router(config-if)#no shutdown 
Router(config-if)#no shutdown Router(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to upRouter(config-if)#ex
Router(config)#int g0/0.1
Router(config-subif)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0.1, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0.1, changed state to upRouter(config-subif)#en
Router(config-subif)#encapsulation d
Router(config-subif)#encapsulation dot1Q 10
Router(config-subif)#
Router(config-subif)#ip add 192.168.50.254 255.255.255.0
Router(config-subif)#ex
Router(config)#int g0/0.3
Router(config-subif)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0.3, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0.3, changed state to upRouter(config-subif)#en
Router(config-subif)#encapsulation do
Router(config-subif)#encapsulation dot1Q 20
Router(config-subif)#ip add 192.168.50.254 255.255.255.0
% 192.168.50.0 overlaps with GigabitEthernet0/0.1
Router(config-subif)#ex
//配ip并开启端口
Router(config)#int g0/1
Router(config-if)#no shutdown 
Router(config-if)#ip add 20.20.20.2 255.255.255.0

运用RIP动态路由

  • 三层交换机
Switch(config-if)#ex
Switch(config)#route rip
Switch(config-router)#version 2
Switch(config-router)#net
Switch(config-router)#network 192.168.10.0
Switch(config-router)#net
Switch(config-router)#network 192.168.20.0
Switch(config-router)#net
Switch(config-router)#network 10.10.10.0
  • R1

Router(config)#route rip
Router(config-router)#version 2
Router(config-router)#net
Router(config-router)#network 192.168.30.0
Router(config-router)#network 192.168.40.0
Router(config-router)#net
Router(config-router)#network 10.10.10.0
Router(config-router)#net
Router(config-router)#network 20.20.20.0
  • R2
Router(config)#route rip
Router(config-router)#version
% Incomplete command.
Router(config-router)#version 22^
% Invalid input detected at '^' marker.Router(config-router)#version 2
Router(config-router)#net
Router(config-router)#network 192.168.50.0
Router(config-router)#network 192.168.60.0
Router(config-router)#net
Router(config-router)#network 20.20.20.0
http://www.xdnf.cn/news/64891.html

相关文章：

  • 20250421在荣品的PRO-RK3566开发板的Android13下频繁重启RKNPU fde40000.npu: Adding to iommu gr
  • Java学习路线--自用--带链接
  • win11修改文件后缀名
  • ADB-＞查看某个应用的版本信息
  • 力扣面试150题--插入区间和用最少数量的箭引爆气球
  • TensorBoard如何在同一图表中绘制多个线条
  • 第 7 篇：总结与展望 - 时间序列学习的下一步
  • k8s集群GPU监控项说明
  • 【人工智能】使用vLLM高性能部署Qwen大语言模型
  • 10天学会嵌入式技术之51单片机-day-2
  • LVGL学习(一)(IMX6ULL运行LVGL,lv_obj_t,lv_obj,size,position,border-box,styles,events)
  • 4·25调价倒计时：SheinTemu美国站价格策略3大关键解读
  • 多路由器通过RIP动态路由实现通讯（单臂路由）
  • Dify忘记管理员密码，重置的问题
  • 数据结构中的各种排序
  • java反射 笔记
  • redis数据类型-位图bitmap
  • Java:多线程
  • C#处理网络传输中不完整的数据流
  • Maxscript调用Newtonsoft.Json解析Json
  • 制作一款打飞机游戏13：状态机
  • 广州可信数据空间上线：1个城市枢纽+N个产业专区+高质量数据集（附28个数据集清单）
  • 如何建设企业级合成数据中台？架构设计、权限治理与复用机制全解
  • 第 3 篇：揭秘时间模式 - 时间序列分解
  • OpenCV基础函数学习4
  • 【油藏地球物理正演软件ColchisFM】ColchisFM正演软件在阿姆河右岸区块礁滩复合体识别中的应用
  • transformer
  • 【Docker-16】Docker Volume存储卷
  • android 多个viewmodel之间通信
  • Android 最简单的native二进制程序