当前位置： 首页 > java >正文

20250823给荣品RD-RK3588开发板刷Rockchip原厂的Buildroot【linux-5.10】时调通AP6275P的WIFI【源码部分】

java 2025/8/24 6:37:50

2、编辑/etc/wpa_supplicant.conf文件
root@rk3588-buildroot:/# cat /etc/wpa_supplicant.conf 
ctrl_interface=/var/run/wpa_supplicant
ap_scan=1
update_config=1

network={
ssid="HONOR70"
psk="13572468"
key_mgmt=WPA-PSK
}
root@rk3588-buildroot:/#


3、【只需执行一次，下次重启就会自动连接了】
然后杀掉已经存在进程
killall wpa_supplicant

重新启动 wpa_supplicant 连接热点
wpa_supplicant -iwlan0 -Dnl80211 -c /etc/wpa_supplicant.conf -B 

获取IP地址
udhcpc -i wlan0

连接成功
ifconfig wlan0
【可选：直接使用ifconfig】

【但是你不执行这些操作，直接重启，就会内核跑飞的！可以这个命令执行了一些操作/写配置文件！^_】


20250823给荣品RD-RK3588开发板刷Rockchip原厂的Buildroot【linux-5.10】时调通AP6275P的WIFI【源码部分】
2025/8/23 15:57


【我是先将这个DTSI文件中的代码块直接搬到rk3588-evb7-lp4.dtsi中，然后就可以上网了。接着就微调到最终版本！】
E:\RD-RK3588_Android13\kernel-5.10\arch\arm64\boot\dts\rockchip\rk3588\rp-wifi-bt-ap6275p-rk3588.dtsi

【这里只有RTC芯片hym8563】
E:\RD-RK3588_Android13\kernel-5.10\arch\arm64\boot\dts\rockchip\rk3588\rd-rk3588.dts
&i2c4 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&i2c4m1_xfer>;

    hym8563: hym8563@51 {
compatible = "haoyu,hym8563";
reg = <0x51>;
#clock-cells = <0>;
clock-frequency = <32768>;
clock-output-names = "hym8563";
//pinctrl-names = "default";
//pinctrl-0 = <&hym8563_int>;
//interrupt-parent = <&gpio0>;
//interrupts = <RK_PD4 IRQ_TYPE_LEVEL_LOW>;
//wakeup-source;
};

};


Z:\Rockchip_RK3588_Linux5.10_SDK_Release_V1.2.0_20230620\kernel\arch\arm64\boot\dts\rockchip\rk3588-evb7-lp4.dtsi

    wireless_bluetooth: wireless-bluetooth {
compatible = "bluetooth-platdata";
clocks = <&hym8563>;
clock-names = "ext_clock";
uart_rts_gpios = <&gpio4 RK_PC4 GPIO_ACTIVE_LOW>;
pinctrl-names = "default", "rts_gpio";
pinctrl-0 = <&uart9m0_rtsn>, <&bt_reset_gpio>, <&bt_wake_gpio>, <&bt_irq_gpio>;
pinctrl-1 = <&uart9_gpios>;
        BT,reset_gpio    = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
BT,wake_gpio     = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
BT,wake_host_irq = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
status = "okay";
};

    wireless_wlan: wireless-wlan {
compatible = "wlan-platdata";
        wifi_chip_type = "ap6398s";
pinctrl-names = "default";
pinctrl-0 = <&wifi_host_wake_irq>;
WIFI,host_wake_irq = <&gpio0 RK_PB2 GPIO_ACTIVE_HIGH>;
WIFI,poweren_gpio = <&gpio0 RK_PC4 GPIO_ACTIVE_HIGH>;
status = "okay";
};

修改为：

    wireless_bluetooth: wireless-bluetooth {
compatible = "bluetooth-platdata";
clocks = <&hym8563>;
clock-names = "ext_clock";
uart_rts_gpios = <&gpio4 RK_PC4 GPIO_ACTIVE_LOW>;
pinctrl-names = "default", "rts_gpio";
pinctrl-0 = <&uart9m0_rtsn>, <&bt_reset_gpio>, <&bt_wake_gpio>, <&bt_irq_gpio>;
pinctrl-1 = <&uart9_gpios>;
        BT,reset_gpio    = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
BT,wake_gpio     = <&gpio2 RK_PB3 GPIO_ACTIVE_HIGH>;
BT,wake_host_irq = <&gpio2 RK_PB0 GPIO_ACTIVE_HIGH>;
status = "okay";
};

    wireless_wlan: wireless-wlan {
compatible = "wlan-platdata";
        wifi_chip_type = "ap6275p";
pinctrl-names = "default";
pinctrl-0 = <&wifi_host_wake_irq>, <&wifi_poweren_gpio>;
WIFI,host_wake_irq = <&gpio0 RK_PB0 GPIO_ACTIVE_HIGH>;
WIFI,poweren_gpio = <&gpio0 RK_PB2 GPIO_ACTIVE_HIGH>;
status = "okay";
};


&i2c6 {
status = "okay";

    hym8563: hym8563@51 {
compatible = "haoyu,hym8563";
reg = <0x51>;
#clock-cells = <0>;
clock-frequency = <32768>;
clock-output-names = "hym8563";
pinctrl-names = "default";
pinctrl-0 = <&hym8563_int>;
interrupt-parent = <&gpio0>;
interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>;
wakeup-source;
};
};

修改为：

//&i2c6 {
//    status = "okay";
//
//    hym8563: hym8563@51 {
//        compatible = "haoyu,hym8563";
//        reg = <0x51>;
//        #clock-cells = <0>;
//        clock-frequency = <32768>;
//        clock-output-names = "hym8563";
//        pinctrl-names = "default";
//        pinctrl-0 = <&hym8563_int>;
//        interrupt-parent = <&gpio0>;
//        interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>;
//        wakeup-source;
//    };
//};

&i2c4 {
status = "okay";
pinctrl-0 = <&i2c4m1_xfer>;

    hym8563: hym8563@51 {
compatible = "haoyu,hym8563";
reg = <0x51>;
#clock-cells = <0>;
clock-frequency = <32768>;
clock-output-names = "hym8563";
pinctrl-names = "default";
//pinctrl-0 = <&hym8563_int>;
//interrupt-parent = <&gpio0>;
//interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>;
//wakeup-source;
};


&pcie2x1l0 {
reset-gpios = <&gpio1 RK_PB4 GPIO_ACTIVE_HIGH>;
status = "okay";
};

修改为：

&pcie2x1l0 {
    phys = <&combphy1_ps PHY_TYPE_PCIE>;
reset-gpios = <&gpio1 RK_PB4 GPIO_ACTIVE_HIGH>;
vpcie3v3-supply = <&vcc3v3_pcie30>;
status = "okay";
};


&pinctrl {

    hym8563 {
hym8563_int: hym8563-int {
rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>;
};
};

    wireless-bluetooth {
uart9_gpios: uart9-gpios {
rockchip,pins = <4 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
};

        bt_reset_gpio: bt-reset-gpio {
rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
};

        bt_wake_gpio: bt-wake-gpio {
rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
};

        bt_irq_gpio: bt-irq-gpio {
rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
};
};

    wireless-wlan {
wifi_host_wake_irq: wifi-host-wake-irq {
rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_down>;
};
};
};

修改为：

&pinctrl {

//    hym8563 {
//        hym8563_int: hym8563-int {
//            rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>;
//        };
//    };

    wireless-bluetooth {
uart9_gpios: uart9-gpios {
rockchip,pins = <4 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
};

        bt_reset_gpio: bt-reset-gpio {
rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
};

        bt_wake_gpio: bt-wake-gpio {
rockchip,pins = <2 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
};

        bt_irq_gpio: bt-irq-gpio {
rockchip,pins = <2 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
};
};

    wireless-wlan {
wifi_host_wake_irq: wifi-host-wake-irq {
rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_down>;
};
};

wifi_poweren_gpio: wifi-poweren-gpio {
rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>;
};
};


参考资料：
https://doc.rpdzkj.cn/#/zh_cn/%E7%91%9E%E8%8A%AF%E5%BE%AE%E7%B3%BB%E5%88%97/rk3588-rk3588s/7.%E6%8E%A5%E5%8F%A3%E4%BD%BF%E7%94%A8?id=buildroot
接口使用

Buildroot
Buildroot 上使用 wpa_supplicant 进行连接

http://www.xdnf.cn/news/18561.html

相关文章：

  • ArkTS 语言全方位解析：鸿蒙生态开发新选择
  • 【AI基础：神经网络】17、神经网络基石：从MP神经元到感知器全解析 - 原理、代码、异或困境与突破
  • 线程间Bug检测工具Canary
  • uniapp 页面跳转及字符串转义
  • Redis学习笔记 ----- 缓存
  • rust语言 (1.88) egui (0.32.1) 学习笔记（逐行注释）（八）按键事件
  • 大语言模型应用开发——利用OpenAI函数与LangChain结合从文本构建知识图谱搭建RAG应用全流程
  • 【KO】前端面试七
  • 20250823给荣品RD-RK3588开发板刷Rockchip原厂的Android14【EVB7的V10】时调通AP6275P的WIFI
  • react相关知识
  • GitLab CI：Auto DevOps 全解析，告别繁琐配置，拥抱自动化未来
  • 运行npm run命令报错“error:0308010C:digital envelope routines::unsupported”
  • 二叉树的经典算法与应用
  • 【网安干货】--操作系统基础(上)
  • USRP采集的WiFi信号绘制星座图为方形
  • 新手向：异步编程入门asyncio最佳实践
  • K8s 实战：Pod 版本更新回滚 + 生命周期管控
  • 嵌入式学习日记（33）TCP
  • 【UnityAS】Unity Android Studio 联合开发快速入门：环境配置、AAR 集成与双向调用教程
  • CMake link_directories()详细介绍与使用指南
  • STM32F1 GPIO介绍及应用
  • C/C++三方库移植到HarmonyOS平台详细教程（补充版so库和头文件形式）
  • 凌霄飞控开发日志兼新手教程——基础篇：认识基本的文件内容和相关函数作用（25电赛备赛版）
  • 【序列晋升】12 Spring Boot 约定优于配置
  • Spring发布订阅模式详解
  • Python 调用 sora_image模型 API 实现图片生成与垫图
  • 【论文】Zotero文献管理
  • 为什么应用会突然耗尽所有数据库连接
  • 轮廓检测技术不仅能精确计算图像中的轮廓数量，还能完整记录每个轮廓包含的所有像素点坐标
  • 【0基础3ds Max】捕捉工具详解