当前位置：首页 > ds >正文

3D拟合测量水杯半径

ds 2025/8/24 14:49:05

1，目的。

测量水杯的半径

如图所示：

2，原理。

对 3D 点云对象进行圆柱体拟合，获取拟合后的半径。

3，注意事项。

在Halcon中使用fit_primitives_object_model_3d进行圆柱体拟合时，输出的primitive_parameter包含以下7个参数：
1. ‌参数构成‌
  - 轴线方向向量‌
  3个数值：(a, b, c)
  描述圆柱体轴线的空间方向，满足归一化条件 a² + b² + c² = 1
  . - 轴线上基准点坐标‌
  3个数值：(x0, y0, z0)
  表示轴线上的一个参考点，通常靠近点云的重心
  . - ‌圆柱半径‌
  1个数值：R
  单位为点云的原始坐标系单位（如毫米）
2. 数学验证‌
  
  圆柱表面点需满足方程：
  $\sqrt{(x-x_p)^2+(y-y_p)^2+(z-z_p)^2-[(x-x_p)a+(y-y_p)b+(z-z_p)c]^2}=R$
  其中(x_p, y_p, z_p)为轴线上任意一点

在Halcon中使用fit_primitives_object_model_3d对三维点云进行球体拟合时，输出的primitive_parameter包含以下4个关键参数：
1. 参数构成‌
  ‌球心坐标‌
  包含3个数值：(x, y, z)
  表示拟合球体的中心点在三维空间中的位置
  ‌球体半径‌
  单个数值：R
  单位为点云的原始坐标系单位（如毫米或米）
2. 参数验证方法‌
  ‌数学验证‌：球面点需满足方程 $x-x_0)^2+(y-y_0)^2+(z-z_0)^2=R^2$
  其中(x_0, y_0, z_0)为球心坐标
3. 与其他几何体的区别‌
- ‌圆柱体‌：输出7个参数（轴线方向、基准点、半径）68
- ‌平面‌：输出4个参数（法向量、偏移量）

4，代码。

*参考案例库:fit_primitives_object_model_3d.hdev* ***********************************************************************
* 将输入的 2.5D 图像拟合成圆柱体，并计算显示拟合后的圆柱体半径* 2.5D 图像：在常规二维图像基础上叠加‌**高度或深度数据**‌，形成半三维表达（如灰度值隐含高度信息或直接存储深度通道）*
* ***********************************************************************
dev_update_off ()
dev_close_window ()
* Input: 2.5D image
* tif图像：是HALCON支持的‌高精度图像格式‌，专门用于存储包含复杂信息的图像数据，如3D深度图、工业相机采集的点云数据等*
* 一般由结构光相机，3D扫描仪提供
read_image (XYZ, '3d_machine_vision/segmentation/3d_primitives_xyz_02.tif')
dev_open_window_fit_image (XYZ, 0, 0, -1, -1, WindowHandle)
set_display_font (WindowHandle, 16, 'mono', 'true', 'false')
* Access to (x-, y-, z-)coordinates
access_channel (XYZ, X, 1)
access_channel (XYZ, Y, 2)*  提取第三通道作为深度
access_channel (XYZ, Z, 3)
* Segment cylinder manually
threshold (Z, Region, 0.0, 0.83)reduce_domain (X, Region, XTmp)dev_display (Z)
dev_set_draw ('margin')
dev_set_line_width (2)
dev_set_color ('green')
dev_display (Region)
disp_message (WindowHandle, 'Segment cylinder with a simple threshold', 'window', 12, 12, 'black', 'true')
disp_continue_message (WindowHandle, 'black', 'true')
stop ()
* 
xyz_to_object_model_3d (XTmp, Y, Z, ObjectModel3DID)* 指定 3D 对象的原始类型，拟合算法，输出类型
ParFitting := ['primitive_type','fitting_algorithm','output_xyz_mapping']
ValFitting := ['cylinder','least_squares_huber','true']
* 对 原始对象进行 3D 拟合fit_primitives_object_model_3d (ObjectModel3DID, ParFitting, ValFitting, ObjectModel3DOutID)
* Clear the object model that is no longer used
clear_object_model_3d (ObjectModel3DID)
* Display the result of the fitting
dev_display (Z)
dev_set_draw ('fill')
dev_display_fitting_results (RegionCylinder, RegionSphere, RegionPlane, RegionNone, ObjectModel3DOutID, WindowHandle, [])
dev_update_on ()
clear_object_model_3d (ObjectModel3DOutID)

本地函数：dev_display_fitting_results

* This procedure displays the results of a fitting operation.
* Additionally to the primitive regions, the radius of
* cylinders and spheres is displayed.
* The colors can be specified with the parameter Colors
* in the following manner:
* Color[0] is used for objects which could not be fitted
* Color[1] is used for cylinders：用于圆柱体
* Color[2] is used for spheres：用于球体
* Color[3] is used for planes：用于平面
* 
if (Colors == [])Colors := ['dim gray','forest green','red','slate blue']
endif
NumNone := 0
* 圆柱体数量
NumCylinders := 0
* 球体数量
NumSpheres := 0
* 平面数量
NumPlanes := 0
for Index := 0 to |ObjectModel3DOutID| - 1 by 1object_model_3d_to_xyz (XTmp, YTmp, ZTmp, ObjectModel3DOutID[Index], 'from_xyz_map', [], [])get_domain (XTmp, DomainTmp)* 是否存在原始数据get_object_model_3d_params (ObjectModel3DOutID[Index], 'has_primitive_data', ParamValue)if (ParamValue == 'true')get_object_model_3d_params (ObjectModel3DOutID[Index], 'primitive_parameter', GenParamValuesP)get_object_model_3d_params (ObjectModel3DOutID[Index], 'primitive_type', ParamValue)if (ParamValue == 'cylinder')if (NumCylinders == 0)*-1:表示复制从索引开始剩余的所有对象，注意这里是浅复制copy_obj (DomainTmp, RegionCylinder, 1, -1)* 从拟合的原始数据中获取拟合的圆柱体半径值RadiusCylinder := GenParamValuesP[6]elseconcat_obj (RegionCylinder, DomainTmp, RegionCylinder)RadiusCylinder := [RadiusCylinder,GenParamValuesP[6]]endifNumCylinders := NumCylinders + 1elseif (ParamValue == 'sphere')* 球体情况if (NumSpheres == 0)copy_obj (DomainTmp, RegionSphere, 1, -1)RadiusSphere := GenParamValuesP[3]elseconcat_obj (RegionSphere, DomainTmp, RegionSphere)RadiusSphere := [RadiusSphere,GenParamValuesP[3]]endifNumSpheres := NumSpheres + 1else* 平面情况if (NumPlanes == 0)copy_obj (DomainTmp, RegionPlane, 1, -1)elseconcat_obj (RegionPlane, DomainTmp, RegionPlane)endifNumPlanes := NumPlanes + 1endifelseif (NumNone == 0)copy_obj (DomainTmp, RegionNone, 1, -1)elseconcat_obj (RegionNone, DomainTmp, RegionNone)endifNumNone := NumNone + 1endif
endfor
* 
NumColors := |Colors|
if (NumNone > 0)dev_set_color (Colors[0 % NumColors])dev_display (RegionNone)
endif
if (NumCylinders > 0)dev_set_color (Colors[1 % NumColors])dev_display (RegionCylinder)
endif
if (NumSpheres > 0)dev_set_color (Colors[2 % NumColors])dev_display (RegionSphere)
endif
if (NumPlanes > 0)dev_set_color (Colors[3 % NumColors])dev_display (RegionPlane)
endif
disp_message (WindowHandle, '3D Fitting', 'window', -1, -1, 'black', 'true')
Message := 'Cylinders: ' + NumCylinders
Message[1] := 'Spheres: ' + NumSpheres
Message[2] := 'Planes: ' + NumPlanes
Message[3] := 'Undefined: ' + NumNone
disp_message (WindowHandle, Message, 'window', 40, 12, 'black', 'true')
if (NumCylinders > 0)* Display radius for each cylinderarea_center (RegionCylinder, Area, Row, Column)for Index := 0 to NumCylinders - 1 by 1Radius := int(RadiusCylinder[Index] * 1000)disp_message (WindowHandle, 'Cylinder\nr = ' + Radius + ' mm', 'image', Row[Index], Column[Index], 'white', 'false')endfor
endif
if (NumSpheres > 0)* Display radius for each cylinder spherearea_center (RegionSphere, Area, Row, Column)for Index := 0 to NumSpheres - 1 by 1Radius := int(RadiusSphere[Index] * 1000)disp_message (WindowHandle, 'Sphere\nr = ' + Radius + ' mm', 'image', Row[Index], Column[Index], 'white', 'false')endfor
endif
return ()

查看全文

http://www.xdnf.cn/news/9994.html